E32

Huge selection of sensing heads on plastic or glass fiber optic cables provide solutions for tough problems.
Choose through-beam, diffuse reflective or retro-reflective sensing methods.
Plastic filament cables can be field cut.
Stainless steel "flex" tubing probes retains complex shapes.
Coiled or ultra-flexible cables are ideal for vibrating or reciprocating machinery.
High-temperature and chemical-resistant models available.

E32-V

Increases process productivity by performing operations with the Industy's first, 4-channel sensor inside vacuum chambers.
Snap-on fiber mounting feature provides ease of use.
Single channel flange with screw mounting is also available,
External fiber can be cut to length.
Stainless and fluoro-resin fiber cables are also available.

Lenses extend sensing distances.
Stainless "flex" tubes protect fibers from damage.
Side-view attachments provide space savings.

E39-V

Allows easy setup and check operation of sensor products.
12 segment LED display provides visable indication for critical beam alignment.
Buzzer provides audible signal
Low battery indication.

E3S-X3

Compact amplifier has a rugged metal housing.
Fast response time.
Wire selectable Light-ON / Dark-ON operation.
Enhanced mutual interference protection of sensing heads.
Sensitivity adjuster and stability indication.
Red LED light source.
Built-in AC/DC amplifier.

E3X

Fast 200 µs response time (special 20 µs high-speed response model).
Choose red or green light source for mark detection.
Adjustable 0.01 to 0.1 sec. OFF-delay timer models available.
Self-diagnostic models have alarm output.
Check input for receiver operation.
Easy alignment with blinking light source set up mode.
Built-in AC/DC amplifier.

Digital Fiber Optic Photoelectric Sensor

Power tuning function addresses saturation or insufficient light conditions.
Dual digital display
4 element LED and Auto Power Control ensure stable, long term performance.
Advanced functions include differential operation for minute detection, 2 independent outputs for area detection, remote input function, and counter function.
Improved mobile console.

E3X-DA-N

Gang mounting up to 16 sensors.
Simple teaching for one or multiple amplifiers using the same settings.
Optical communications between amplifiers allows a hand-held programmer to copy/paste or store banks of settings.
Optional network modules allow settings to be made via DeviceNet or CompoBus/S remote I/O network.
Serial network available.
Digital displays show light incident level, percentage and analog levels.

E3X-NA

Cost-effective, wire-saving solution for space-confined sensing applications.
Segment display helps set optimal gain.
Red or green light source for accurate mark detection.
High-speed 50 µs response.
Water-resistant models available.
Connector and pre-wired versions.
Optical communication design prevents mutual interference for up to 5 amplifiers.

Advanced Digital Photoelectric Fiber-Optic Amplifier

Packs two advanced fiber optic sensors in one housing that only measures 10 mm in width.
Built-in AND/OR control output provides more cost savings by eliminating the need for controller hardware
Power Tuning function automatically optimizes sensor performance to the sensi ng conditions.

Fiber Optic Amplifier Communication Unit

Serial communication for RS422.
Reduces wiring with new connectors for easier maintenance.
11.4 - 26.4 VDC power supply.

E3X-NH

Industry's first 16-bit processor in a sensor provides automatic sensitivity adjustment for stable detection in frequently changing environments.
3 teach modes for optimal sensing.
13-point threshold display and 8-point sensitivity meter allow fine-tuning for detection of small objects or fine wires.

E3X-NM / NT

Fast 0.5 ms response time.
Single channel or four-channel models in slim space-saving housings.
Pushbutton sensitivity adjustment simplifies setup, maintenance.
Four-channel model allows independent settings without mutual interference.
40 ms OFF-delay timer available.

E3X-NV / NVG

Red LED source with TEACH function.
Uses our E32 series fiber cables.
Built-in DC amplifier.
Water-resistant IP66 housing.
500 µs response time.
Designed for label and packaging applications.

E3SA

Ideal for analog detection of position, size, surface and color changes.
Fast 1 ms response time.
Small pre-wired DC sensor has built-in amplifier that provides both analog and ON/OFF outputs simultaneously.
4-turn controls allow fine adjustments in sensitivity and output operating point.

E3XA

E3HQ

Teflon housing and cable protect sensor against harsh chemicals.
10 mm housing fits in tight spots.
Built-in amplifier allows direct connection of sensor to interface.
Stainless steel bracket provides simple, secure mounting.
Wide selection of timing options.
NEMA 4X, IP67 rated.